When you look in Pattern-making books they usually have a table of standard measurements including either the bust dart width, or it’s angle in degrees. These “standard measurements” are for a B-cup, which means that if you are *not* a B-cup, you have to draft the pattern and then do either a Small Bust Adjustment or a Full Bust Adjustment.

But how do they get these numbers? They seem to have nothing to do with the rest of the measurements. But there is always a formula. It just takes a bit of working out.

What is a bust dart’s function? As I see it, a bust dart is there to make the longer front pattern piece match the shorter back pattern piece at the side seam. The front pattern piece is longer than the back one because it has your bust to go over and the back doesn’t.

So to find out the bust dart’s width at the side seam,

- you measure your front from the neck point the red dot over the apex (the green dot on the drawing), and thence straight down to your waistline = F; (this measurement is the orange line in the picture)
- then measure from the red dot down your back to your waistline = B; (this is the red line)
- subtract B from F and you have your bust dart width, which is the difference between your front bodice length, and your back bodice length.

#### How to Find Your Bust Dart Angle for Patternmaking in Fashion

If you are using the German method of pattern making, which is briefly taught in *Patternmaking in Fashion *by Lucia Mors de Castro (mine cost about £40 but it now costs £100 at Amazon due to high demand – I think it is over-priced now by very greedy sellers), you will need the angle of the bust dart, and as we have the length of the dart (the hypotenuse) and the width of the dart (the length “opposite” the angle) we can find the Sine of the angle (sin = O/h) and then use the sin^{-1} function on our scientific calculators to find the angle. Thus:-

^{}

#### How to Find Your Bust Dart Width for Metric Pattern Cutting

*Metric Pattern Cutting for Women’s Wear*by Winifred Aldrich, or the instructions on www.BurdaStyle.com, you will want to find the bust dart width for a shoulder dart.

- Take the sine you found earlier (here 0.077) and multiply it by your neck to apex measurement (on me about 24 cm) to get
*half*your total bust dart width. (Here, about 1.84 cm). - Get your total bust dart width by doubling this number = 3.68 cm, roughly
.__3.7 cm__

**Sabrina**
Thank you, this helps a lot.

LikeLike

Hi Ms. Wharton-Brown,

Here is a tutorial that may supplement your wonderful article. Please check it out.

Thank you.

http://kosherpatterns.com/tutorials2/24-how-to-add-a-bust-dart-to-a-dartless-pattern.html

LikeLike

hi, my name is Prime. Ur article was really helpful. Two questions please: how did u get the first length of the bust dart?, and what did u mean when u said only half, that is 4.4 in ur case would be used? (the mention of 8.8 later for the got me a bit confused too)

LikeLike

#for the shoulder dart#

LikeLike

The length of the first bust dart is the distance from where your side seam would be (you can guess this by where it feels right) to the bust point.

About the “half”: the bust dart is a triangle, and if you divide it down the middle, halving it, you get two right-angle triangles which are much easier to work with mathematically.

Because we divided the bust dart in two (so that we could use a right-angle triangle) the angle measurements and the length of the side marked “opposite” in the picture, are half what they would be for a full bust dart. That is why the 4.4º gets doubled to make 8.8º.

The 4.4º comes about from having your scientific calculator do some backward trigonometry. If you type in “Sinˆ-1 0.077 =” on your scientific calculator it will give you the number 4.4.

Thank you for commenting. I thought I had added more images to this post than I had, so I'll add them now, and that should help to illustrate the information.

LikeLike

The shoulder dart is the Metric Pattern Cutting one.

LikeLike

Thank you so much for this tutorial

LikeLike